Cardboard Cutting Plotter 200-2000mm/s | for Packaging

Tool Head Configured Per Material — A packaging shop running E-flute one hour and 12mm EVA foam the next needs oscillating knife, creasing wheel and V-groove available on one table, not three separate machines.

Technical Specifications

Application Suitability

What "Cutting Speed Up to 1500 mm/s" Actually Means on Corrugated Board

The speed number on the spec sheet is the empty-travel maximum; your real production speed depends entirely on ply count, flute profile and whether you are cutting, creasing or kiss-cutting in the same pass.

I once watched a packaging sample room in Suzhou try to run triple-wall BC-flute at the same feed rate they used for single-face E-flute. The oscillating knife dragged, the cut edge compressed rather than sheared, and every corner radius came out jagged. The operator spent the next four hours dropping the speed in increments until the edge quality returned. A packaging CNC cutting machine production line does not have a single throughput number — it has a matrix of speeds tied to specific board grades, and that matrix only gets built by running your own stock on the table before the order is finalized. [NEED_CITE: oscillating knife cutting speed versus corrugated flute type]

Tool Head Selection Dictates Edge Quality More Than Speed Does

When a carton sample maker switches between 3mm E-flute for cosmetics boxes and 15mm EVA foam for electronics inserts, the oscillating knife handles the foam cleanly but crushes the flute on the corrugated board if the creasing wheel is not swapped in. The 1625(std.) carries up to seven tool options on one gantry — oscillating knife, driven rotary, creasing wheel, kiss cutting, pneumatic knife, milling and V-groove — so the packaging CNC cutting machine production line covers the entire carton-and-insert workflow without a second machine. The creasing wheel scores without penetrating the liner, the V-groove knife removes a precise strip for rigid box corners, and the kiss cutting tool slices the top ply for tear-off strips.

Vacuum Table Zoning and Small-Part Hold-Down

A full-sheet vacuum table pulls evenly across a 1600×2500 mm bed, but once the knife slices a sheet of greyboard into twenty small carton blanks, only the zones still covered by material maintain suction. The aluminum bellows vacuum table on this packaging CNC cutting machine production line divides suction into addressable sections so that a 60×60 mm gasket piece stays flat while the knife exits the cut. [NEED_CITE: vacuum zoning requirements for small-part digital cutting] Without zoning, the trailing edge of a small part lifts into the knife path, producing a nick or a shifted cut that pushes dimensions outside the ±0.1 mm accuracy band.

Reading the Spec Sheet Against Your Actual Material Stack

The ≤ 40 mm cutting thickness figure is the mechanical stroke limit of the oscillating knife head; whether it actually shears through 40 mm of PU foam in one pass depends on foam density and whether the material is free-standing or adhesive-backed. The 9 kW vacuum pump must overcome the porosity of corrugated flutes — air leaks through the open channels of a B-flute sheet far faster than through a solid PET panel, so pump capacity and table zoning together determine whether small blanks stay registered. Servo drive selection (Panasonic, Delta, or Dorna) affects acceleration on short linear segments typical in carton layouts with dozens of flap folds, and that acceleration directly influences cycle time more than the headline top speed.

The Cost of Specifying a Machine on Working Area Alone

I visited a carton shop in Hangzhou that bought a flatbed table solely because the bed size matched their largest sheet. When they loaded 800 gsm greyboard for rigid boxes, the vacuum hold-down was insufficient for the narrow strip pieces, and the oscillating knife deflected on the dense stock, producing beveled edges that would not fold square. They eventually retrofitted a higher-capacity pump and re-zoned the table, but the two weeks of scrap board and the missed sample deadline cost them a cosmetics client. [NEED_CITE: packaging material density and vacuum hold-down requirements]

Why Source This Machine Here

The manufacturer designs and builds both knife and laser cutting systems in-house, so a packaging buyer can match the cutting method to the material rather than forcing one technology across every substrate. Each tool head and table configuration is specified against the buyer’s declared material range and smallest part size, not pulled from a standard list. A sample cutting report on the buyer’s own corrugated board, foam or composite stock is generated before the order is confirmed, documenting edge quality, crease depth and dimensional accuracy. Voltage, plug type and control language are locked in the electrical schematic before the machine enters assembly, avoiding the on-site transformer scramble that delays commissioning. The dedicated packaging box structure design software reads PLT, DXF, AI and PDF natively, so the sample room’s existing file library transfers without format conversion.

Documentation & Verification

• Factory test record on buyer’s corrugated and foam stock before dispatch
• Electrical schematic confirming voltage, plug type and circuit rating for target market
• Tool head and vacuum zoning configuration list matched to buyer’s material range
• Software licence, file format compatibility note and control language confirmation
• CE declaration covering machinery directive scope for this oscillating knife table
• Operation manual with maintenance intervals specific to the configured servo drive

Installation, Commissioning & Support

• Fully assembled 3300×2100×1350 mm frame requires level concrete floor with no anchor bolts
• Dedicated 380V three-phase circuit with isolated neutral for the 9 kW vacuum pump
• PLC control panel pre-loaded with packaging software and buyer’s confirmed language option
• First-run parameter tuning on buyer’s actual board grades and foam densities during commissioning
• Oscillating knife blade and creasing wheel wear parts list with reorder intervals included
• Infrared safety sensor calibration verified across the full 1600×2500 mm working area on site

What to Include in Your Inquiry

Send the specific corrugated flute profiles, foam densities and sheet sizes you run most often, along with the smallest part dimension in your current carton library. Confirm the voltage and frequency at your facility, the control language your operators need, and whether your existing design files are in PLT, DXF, AI or PDF format. If you need a sample cut on your own material before committing, ship a few sheets to the factory so the tool head and vacuum zoning can be validated against your actual production mix.

Frequently Asked Questions

Q: How is cutting capacity verified for my specific corrugated ply or foam thickness?
A: Before the order is locked, the factory runs your material on the table and records cutting speed, edge quality and crease definition in a sample cutting report. The ≤ 40 mm stroke limit is mechanical, but actual shearing performance depends on flute profile, foam density and whether adhesive backing is present, so the test confirms real behavior, not catalog claims.

Q: Which tool head is selected for my material mix?
A: The configuration is matched to your declared substrates. E-flute and B-flute typically use the oscillating knife for cuts and the creasing wheel for fold lines. EVA and PU foam call for the oscillating knife at adjusted stroke frequency. Rigid box corners use the V-groove tool. The machine supports up to seven tools on one gantry, so all your materials are covered in one setup.

Q: How are voltage, plug type and control language confirmed before shipment?
A: The electrical schematic is drafted with your facility’s voltage and frequency, and the plug type is documented before assembly begins. The PLC control panel is loaded with the operator language you specify — standard options include English, Russian, Italian and Chinese, with special languages available on request.

Q: What is the footprint and installation requirement on the production floor?
A: The machine measures 3300×2100×1350 mm and ships fully assembled, so no on-site frame bolting is needed. You need a level concrete floor and a dedicated circuit for the 9 kW vacuum pump. The aluminum bellows vacuum table requires no external plumbing beyond the pump connection.

Q: Can I run a sample cut on my own packaging material before committing to the order?
A: Yes. Ship a few sheets of your actual corrugated board, foam or composite stock to the factory. The sample cutting report documents edge quality, dimensional accuracy against the ±0.1 mm spec and crease definition, so you can evaluate production readiness before the purchase is finalized.